Office Evolution Overview

First page Previous page 18 Next page Last page

SAMPLE FLOOR PLANS

7,000 SQUARE FEET

Finish Plan General Notes

Finish Plan Key Notes

Symbol Legend

Submittals - Contractor to submit samples of all finishes to NELSON for approval prior to ordering/installation.

Floor Finish - Transition

1. Existing Surfaces Repair The Contractor shall retouch or refinish surfaces damaged by subsequent work. 2. Existing Surfaces

Office 114

Office 115

Key - Floor Finish

CPT-1

Office 116

Office 117

Office 118

Corner Guard - Provide and install wall edge protection on all outside corners. Specification: TBD

Office 113

Contractor shall examine all surfaces to be finished under this contract and see that the work of their trades has been installed in satisfactory condition to receive paint, stain or specified finish. The application of the first coat of any finish process shall constitute acceptance by the Contractor of the surface. 3. Existing Finishes Where new finishes are adjacent to existing finishes, materials shall be installed with no definitive transitions between existing and new finishes. 4. Material Packaging/ Storage/ Installation Materials shall be delivered in their original cartons as packaged by the manufacturer and must bear the original manufacturer's labels. Contractor will be responsible for receiving and storing such goods. Materials stored on the site shall be protected from damage by moisture, wind, sun, abuse or any other harmful affects. Damaged materials will be rejected and must be replaced. All materials shall be installed and finished according to manufacturer's specifications. 5. Preparation for Installation Contractor shall examine conditions concerning substrates and surfaces where finish work is to be performed. All substrates and surfaces to receive finishes shall be free of dirt and debris prior to installation. Both the substrate and surface preparation shall be in accordance with the manufacturer's recommendations. 6. Carpet Contractor shall submit three (3) sets of carpet samples to NELSON for approval prior to field execution. Contractor shall ensure that carpet supplied for an individual installation be from the same manufacturing run, of uniform color, texture and pattern. 7. Carpet Installation All flooring shall be installed per manufacturer's recommendations regarding adhesives, seaming, direction, etc. Carpet installer shall ensure that carpet nap runs in the same direction. Carpet to carpet transitions at door shall occur directly under line of closed door. 8. Carpet Stock The Contractor shall verify whether or not the Tenant would like to store any large usable carpet remnants prior to discarding. 9. Base Contractor shall allow rubber base to run continuous around corners. Do not use pre-molded base or pieces less than 18" long. Base material shall be installed flush to floor surface. 10. Transitions Contractor shall provide rubber transition strips between carpet and LVT/VCT to match rubber base. 11. Paint All painted surfaces shall receive manufacturer's recommended primer coat and (2) coats minimum specified finish. 12. Paint Submittals Contractor shall submit three (3) sets of 8" x 10" paint samples to NELSON for approval prior to field execution. 13. Paint Stock Contractor shall leave remaining paint (1 gallon minimum) of each color clearly labeled with "Color Name" and Finish Key "P-#" with Tenant for future touch-up needs. 14. Wallcovering Wall or surfaces with wallcovering finishes shall be primed with sizing prior to wallcovering installation. Wallcovering installations shall not terminate at outside corners or reveals. If it is necessary to terminate wallcovering on a flat wall or outside corner, provide edge mold: Outside Corners: Koroseal, Korogard OC12 Aluminum Outside Corner Trim Piece Flat Walls: Koroseal, Korogard JC12 J-Molding 15. Clean Up Upon completion of all finish applications, all materials and equipment shall be removed. Contractor shall ensure that paint and glue spots are removed and that all areas are left clean and free of dust, dirt and debris. 16. Interior Finish Code Compliance Finish requirements per 2012 NFPA 101 Section 38.3.3 Interior Finish for New Business Occupancies: 38.3.3.1 Interior finish shall be in accordance with Section 10.2. 38.3.3.2.1 Interior wall and ceiling finish material complying with Section 10.2 shall be Class A or Class B in exits and in exit access corridors. 38.3.3.2.2 Interior wall and ceiling finishes shall be Class A, Class B, or Class C in areas other than those specified in 38.3.3.2.1. 38.3.3.3.1 Interior floor finish shall comply with Section 10.2. 38.3.3.3.2 Interior floor finish in exit enclosures shall be Class I or Class II. 38.3.3.3.3 Interior floor finish shall comply with 10.2.7.1 or 10.2.7.2, as applicable. 12 13 14 15 16

CPT-2

Key - Wall Finish

P-1

CPT-2

Key - Note

Finish Schedule CPT-1 Carpet Tile Manufacturer: Patcraft Style: Color Pop 10381 Color: Retro Pop 00650 Installation: Coordinate with Tenant

P-1 Paint Manufacturer: TBD Color: TBD Two (2) coats eggshell To be used throughout unless otherwise noted. P-2 Trim Paint Manufacturer: TBD Color: TBD Two (2) coats semi-gloss To be used on h.m. frames throughout.

Office 112

CPT-2

Office 119

Office 123

Office 120

Office 122

Office 121

To be used throughout unless noted otherwise. Contact Tracy Roan with Patcraft @ 404.316.4631 CPT-2 Carpet Tile Manufacturer: Patcraft Style: Color Block 10382 Color: 00650 Installation: Coordinate with Tenant To be used where indicated. Contact Tracy Roan with Patcraft @ 404.316.4631 LVT-1 Luxury Vinyl Tile Manufacturer: Patcraft Style: North Ridge 1206V Color: Irish Cream 02150 Size: 3 x 36 Pattern: Coordinate with Tenant To be used where indicated. Contact Tracy Roan with Patcraft @ 404.316.4631

CPT-2

Office 111

CPT-2

P-3 Accent Paint Manufacturer: TBD Color: TBD Two (2) coats eggshell Locations TBD PL-1 Plastic Laminate Manufacturer: Formica Color: Ebony 9012 See Details PL-2 Plastic Laminate Manufacturer: Formica Color: Neutral Weft 5875 See Details

Office 110

Office 108

Office 124

Office 125

CPT-2

Office 109

CPT-2

CPT-1 P-1 RB-1

Typ. Typ.

Office 106

Break 126

Typ.

Office 107

VCT-1 Vinyl Composition Tile Manufacturer: TBD Style: TBD Color: TBD Size: 12 x 12 To be used where indicated.

CPT-2

Copy/Mail 128

Office 105

RB-1 Rubber Base Manufacturer: Johnsonite Style: 4" Cove Color: 48-Gray To be used throughout.

Drop In 127

CPT-2

Conference 2 129

Office 104

CPT-1

CPT-2

Reception 100

IT 130

VCT-1

LVT-1

Office 103

Conf. 1 131

Office 102

Office 101

CPT-2

CPT-1

CPT-2

CPT-2 23

REFER TO SHEET A201 FOR FINISH LEGEND AND S FINISH PLAN IS NOT REPRESENTATIVE OF ALL FINI DETERMINE AVAILABILITY OF ALL MATERIALS DUR BIDDING AND PRICING PHASE. BRING ANY DELIVE MAY CAUSE COORDINATION PROBLEMS DURING T STAGES OF CONSTRUCTION TO THE ATTENTION O ARCHITECT AS SOON AS POSSIBLE. EXTEND ALL FINISHES (INCLUDING PAINT) BENEAT AND AROUND ALL NEW AND EXISTING TO REMAIN CASEWORK, EQUIPMENT, SIGNAGE, ETC. WHETHE INDICATED OR NOT. PROVIDE AND INSTALL RUBBER TRANSITION STRIP RUBBER BASE BETWEEN CARPET. REFER TO SHE FOR FLOOR TRANSITION DETAILS. ALIGN ALL FLOORING TRANSITIONS WITH CENTER DOOR OR FACE OF ADJACENT WALL UNLESS NOTE OTHERWISE. PROVIDE LEVEL 5 FINISH AT ALL DIRECT APPLIED GRAPHIC/FILM WALLS AND MARKERBOARD PAINT

Finish Plan Scale: 1/8" = 1'-0"

1 I-7

11,000 SQUARE FEET

OFFICE 137

OFFICE 144

FLOORING TO BE CPT-01 UNLESS NOTED OTHERW

OFFICE 145

OFFICE 139

OFFICE 140

OFFICE 141

OFFICE 142

OFFICE 143

WALL BASE TO BE RWB-01 UNLESS NOTED OTHER

WALL FINISH TO BE PNT-01 UNLESS NOTED OTHER

DROP-IN 138

DOOR FRAMES TO BE PNT-05 UNLESS NOTED OTH

GYPSUM BOARD CEILINGS AND SOFFITS TO BE PN UNLESS NOTED OTHERWISE.

1 TYP.

OFFICE 136

1 TYP.

OFFICE 146

OFFICE 131

OFFICE 135

OFFICE 134

OFFICE 133

OFFICE 132

GENERAL NOTES 1/8" = 1'-0"

OFFICE 130

OFFICE 147

OFFICE 124

2" STAINLESS STEEL 4' HIGH CORNER GUARD AT ALL OUTSIDE CORNERS, ABOVE BASE, TYP.

OFFICE 126

OFFICE 127

ALIGN FINISHES

2 3

BREAKROOM 125

MATCH EXISTING FINISHES

OFFICE 129

OFFICE 148

IT 128

OFFICE 123

CPT-01

CORRIDOR 149

COATS 122

CPT-02

COPY/MAIL 102

OFFICE 121

OFFICE 122

OFFICE 117

OFFICE 116

LVT-01

HUDDLE 2 113

HUDDLE 1 114

RECEPTION 101

OFFICE 104

OFFICE 120

OFFICE 119

OFFICE 118

OFFICE 115

1 TYP.

CONFERENCE 103

OFFICE 105

OFFICE 112

OFFICE 106

OFFICE 107

OFFICE 108

OFFICE 109

OFFICE 110

OFFICE 111

Construction specifications are available for test fit and pricing.

A Industry Overview

OE Overview

Team & Timeline

Locations

FINISH PLAN 1/4" = 1'-0" Corporate Support A08

KEYNOTES 1/8" = 1'-0" Customer Pr A0

Made with FlippingBook - Online Brochure Maker